Description
Product
Specs
Buyers
Guide
FAQ's
Downloads
Remanufactured products only require 15-20% of the total energy and material it takes to manufacture new parts while keeping usable cores out of landfills.
CARDONE's skilled technicians and engineers can completely rebuild your part and return it to you, good as new. Learn More.
Product Description
Expertly remanufactured to rigorous quality and performance standards, CARDONE Electronic Power Steering Rack and Pinions are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. Each unit undergoes CARDONE’s Factory Test Drive, simulating extreme operating conditions while verifying all on-car communications. All rubber sealing components are replaced, and a specialized lubricant is applied to drastically increase longevity.
Complete the Check It Fits tool and confirm all information in the Fitment Details section above to ensure you select the right part for your application.
Metafield Product & Technical
What do you replace on the rack?
Rubber seals, dust boots, wear items, lubricant(s), clamps and bearings are replaced 100%. Dampers, lock washers and drive belts are replaced where applicable.Are there any precautions before I install?
Yes, the steering wheel must be held in a straight-ahead position using a suitable tool to prevent rotation while the intermediate shaft is disconnected from the rack and pinion. Failure to do so can result in damage to the clock spring within the steering column. If rotation of the intermediate shaft is suspected, the clock spring must be removed and re-centered.Are the racks the same design as my original?
Yes, all units produced are verified to function to O.E. design specifications. Potential O.E. failure modes are evaluated and validated improvements are made.Do I have to do any type of relearn after installation?
Yes, these systems are equipped with torque angle sensors in the steering column that need to be recalibrated after installation of the replacement rack and pinion.Can I install one of your racks on my custom or classic vehicle?
Not recommended; radical modifications would be needed for installation of a modern electronic steering rack and pinion on a vehicle other than the O.E .Manufacturer intended application.
Core
What is a core? A core is a used automotive part that is returned to the remanufacturer instead of being scrapped. Why return cores? Cores are literally at the “core” of the remanufacturing process, because they are the raw material used to start the remanufacturing process. That’s why remanufacturers buy cores back from customers, and they pay the most for good quality cores. If a core has too much damage in key areas, it may be unusable or require extra resources to process; therefore a reduced core payment may be awarded. This core policy explains potential deductions that may be taken from the core price if certain components are missing or damaged. What is remanufacturing? Remanufacturing is the process of taking used parts, completely disassembling and thoroughly cleaning them, replacing the worn components with original quality components, and restoring them to their original function. Every unit is 100% tested to ensure O.E. performance. Why “reman”? PRODUCTS - Reman captures used, durable goods like auto parts and puts them “back on the road” to new and sometimes better than new performance. Reman provides the opportunity for detection of common failure modes and incorporation of design improvements to prevent repeat failure.ECONOMY - Reman products cost consumers about 40% less than new. Reman products are one of the few “green” products that actually costs less than their “non-green” counterparts.
ENVIRONMENTAL - Reman saves up to 86% of the energy required to build a new unit. Reman realizes Greenhouse Gas savings of up to 25 lbs. per unit over new. Reman saves up to 85% of the raw material required to produce a new unit by reusing existing products. Reman is even more sustainable than recycling, as product castings are preserved rather than melted down to raw material, saving energy and reducing emissions.
Warranty Policy
Installation & Tech Checks
Core Policy
ProTech Bulletins
General
pdm:general_part_type:
Rack and Pinion Assembly
pdm:general_product_condition:
Remanufactured
Life Cycle Status:
Available to Order
pdm:general_package_contents:
Rack and Pinion; Instruction Sheet
pdm:general_package_weight:
13.93 lb
UPC:
00884548285262
pdm:general_e_waste:
No
Technical
Bellows Color:
BLACK
Casting Material:
ALUMINUM
Color or Finish:
BLACK
Distance Between Mounting Holes - Imperial:
17.13 in
Distance Between Mounting Holes - Metric:
434.98 mm
Gasket or Seal Included:
NO
Grade Type:
Regular
Input Shaft Diameter - Imperial:
0.76 in
Input Shaft Diameter - Metric:
19.25 mm
Input Shaft Length - Imperial:
3.88 in
Input Shaft Length - Metric:
98.43 mm
Mounting Bracket Included:
NO
Number of Mounting Holes:
2
Outer Tie Rods Included:
NO
Rack Length - Imperial:
47.75 in
Rack Length - Metric:
1212.85 mm
Thread Length - Imperial:
2.195 in
Thread Length - Metric:
55.75 mm
Tie Rod Ends Included:
Yes
Total Turns Lock to Lock:
3.31
pdm:Bellows Color:
Black
pdm:End To End Length:
47.75 IN
pdm:End To End Length:
1212.37 MM
pdm:Gasket Or Seal Included:
No
pdm:Grade Type:
Regular
pdm:Inner Tie Rods Included:
Yes
pdm:Input Shaft Type:
Double Flat
pdm:Mounting Brackets Included:
No
pdm:Mounting Hardware Included:
No
pdm:Mounting Hole Quantity:
2
pdm:Outer Tie Rods Included:
No
pdm:Steering Input Shaft Diameter:
19.25 MM
pdm:Steering Input Shaft Diameter:
0.758 IN
pdm:Total Turns Lock To Lock:
3.312
pdm:Type:
Manual
General
Part Type:
Rack and Pinion Assembly
Product Condition:
Remanufactured
Lifecycle Status:
Available to Order
Package Contents:
Rack and Pinion; Instruction Sheet
Packaged Weight:
13.9250 lb
E-Waste:
NO
Warranty:
3 Year/36,000 Mile
*A warranty must be returned to the parts supplier where the CARDONE product was
purchased and is subject to that part store's terms & conditions. If the parts retailer offers a
different warranty than the CARDONE warranty, the retailer’s policy will prevail.
Technical
Bellows Color:
BLACK
Casting Material:
ALUMINUM
Color or Finish:
BLACK
Distance Between Mounting Holes - Imperial:
17.13 in
Distance Between Mounting Holes - Metric:
434.98 mm
Gasket or Seal Included:
NO
Grade Type:
Regular
Input Shaft Diameter - Imperial:
0.76 in
Input Shaft Diameter - Metric:
19.25 mm
Input Shaft Length - Imperial:
3.88 in
Input Shaft Length - Metric:
98.43 mm
Installation Hardware Included:
no
Mounting Bracket Included:
NO
Number of Mounting Holes:
2
Outer Tie Rods Included:
NO
Rack Length - Imperial:
47.75 in
Rack Length - Metric:
1212.85 mm
Thread Length - Imperial:
2.195 in
Thread Length - Metric:
55.75 mm
Tie Rod Ends Included:
Yes
Total Turns Lock to Lock:
3.31
Type:
Manual
pdm:Bellows Color:
Black
pdm:End To End Length:
47.75 IN
pdm:End To End Length:
1212.37 MM
pdm:Gasket Or Seal Included:
No
pdm:Grade Type:
Regular
pdm:Inner Tie Rods Included:
Yes
pdm:Input Shaft Type:
Double Flat
pdm:Mounting Brackets Included:
No
pdm:Mounting Hardware Included:
No
pdm:Mounting Hole Quantity:
2
pdm:Outer Tie Rods Included:
No
pdm:Steering Input Shaft Diameter:
19.25 MM
pdm:Steering Input Shaft Diameter:
0.758 IN
pdm:Total Turns Lock To Lock:
3.312
pdm:Type:
Manual
