![Click for more info Click for more info](https://cdn11.bigcommerce.com/s-z9vhe3o238/product_images/uploaded_images/sustainablepdpbadge.png)
Product Description
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.
Complete the Check It Fits tool and confirm all information in the Fitment Details section above to ensure you select the right part for your application.
Year
Make
Model
Engine
QualifierText
Position
2014
Cadillac
CTS
2.0L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2010 - 2014
Cadillac
CTS
3.0L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2008 - 2014
Cadillac
CTS
3.6L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2009 - 2014
Cadillac
CTS
6.2L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2004 - 2009
Cadillac
SRX
3.6L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2004 - 2009
Cadillac
SRX
4.6L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2005 - 2011
Cadillac
STS
3.6L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2006 - 2009
Cadillac
STS
4.4L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
2005 - 2010
Cadillac
STS
4.6L
with 25.59 (in) Long Driveshaft
Measurement taken from end of CV joint flange face to end of CV joint flange face
Supplied as New
Front
Product & Technical
What causes prop shaft vibration?
The most common causes of prop shaft vibrations are worn joints, an unbalanced drive shaft, poor joint lubrication, and a bent or twisted shaft.Are your shafts balanced? Why is it necessary?
Each shaft is precisely balanced before boxing. Prop shaft balance is necessary for proper driveline operation. An unbalanced shaft can cause premature wear on other major components such as your transmission and rear differential.How is a prop shaft balanced?
This procedure entails the distribution of mass in the rotating prop shaft. The shaft is measured and altered where necessary to ensure that vibration does not occur during operation.What is prop shaft phasing?
Phasing is a used to describe the alignment of the yokes with each other at both ends of the prop shaft. The phase angle is the rotational position of each yoke on a prop shaft.Do all vehicles have prop shafts?
Not all vehicles will have a prop shaft. Prop shafts are most commonly found on all-wheel-drive and rear- wheel-drive vehicles.What is a universal joint?
A universal joint is designed to allow prop shafts to move with suspension travel while the shaft is moving. This allows power to be transmitted when the prop shaft is angled between the transmission and differential.Warranty Policy
Installation & Tech Checks
Core Policy
ProTech Bulletins
General
part type:
Drive Shaft
product condition:
New
Life Cycle Status:
Available to Order
package contents:
Prop Shaft; Instruction Sheet
package weight:
16.00 lb
UPC:
00884548216099
e waste:
No
OE Numbers
Cadillac
15212141, 25768518
Technical
Greasable:
Yes
Length - Imperial:
25.59 in
Length - Metric:
650 mm
Measurement Method:
Measurement taken from end of CV joint flange face to end of CV joint flange face
Shaft Material:
Steel
Tubing Outer Diameter - Imperial:
1.75 in
Tubing Outer Diameter - Metric:
50 mm
CV Joints Included:
Yes
Compressed Length:
25.59 IN
Compressed Length:
650.00 MM
Drive Shaft Type:
CV
End 1 Type:
Bolt On
End 2 Type:
Bolt On
Grade Type:
Regular
Greasable:
No
Grease Fitting Included:
No
Phased:
Yes
Pre-Greased:
Yes
Shaft Diameter:
1.75 IN
Shaft Diameter:
50.00 MM
Shaft Material:
Steel
Slip Yoke:
No
Universal Joints Included:
Yes